My button won’t close anymore when i delete this part of the code it wants to close but now it doesn’t, So i assume something is wrong here
[If, result == 9, //Without this one everything woks
[VarSet, ButtonNo3, 2]
[NoteIButton, “Yes”,0xff9923]// button1
[NoteIButton, “No”,0xff9923]// button2
[VarSet,result,[Note,"\Cff9923 Make new UVs?
",0x282f42,400]]
[If, result == 1,
[Note, “Please go Back to EaZy Exploder and hit UVs Used”]
[VarSet, makeUv, 1]
[IPress, Zplugin:Uv Master:Unwrap]
[IPress, Zplugin:Uv Master:Flatten]
]
[If, result == 2,
[RoutineCall, Part2]
]
[LoopExit]
]
//_______________________________________________________whole code
[IButton, “Explode”,“EaZy Exploder”,
[IPress, Tool:Visibility:ShowPT]
[IPress, Tool:Subtool: Duplicate]
[VarSet, sTNr, [SubToolGetActiveIndex]+1]
[SubToolSelect, sTNr]
[VarSet, sTNr, 0]
[IPress, Tool:Visibility:ShowPT]
[VarSet, sDIV, [IGetMax, Tool:Geometry:sDIV]-[IGet, Tool:Geometry:sDIV]]
[IPress, Tool:Layers:Bake All]
[Loop, sDIV,
[IPress,Tool:Geometry:Higher Res]
]
[VarSet, sDIV, [IGet, Tool:Geometry:sDIV]-1]
[IPress, Tool:Subtool:Duplicate]
[IPress,Tool:Geometry:Del Lower]
[VarSet, sTNr, [SubToolGetActiveIndex]+1]
[SubToolSelect, sTNr] //____goes to lp procces
[ISet, Tool:Geometry:AdaptiveSize, 50]
[ISet, Tool:Geometry:Curves Strength, 50]
[IPress, Tool:Geometry:Adapt]
[IUnPress, Tool:Geometry:FreezeBorder]
[IUnPress, Tool:Geometry:FreezeGroups]
[IUnPress, Tool:Geometry:KeepGroups]
[IUnPress, Tool:Geometry:Use Polypaint]
[VarSet, ButtonNo, 4]
[NoteIButton, “Use Lowest sDIV”,0xff9923]// button1
[NoteIButton, “Use Styx”,0xff9923]// button2
[NoteIButton, “Import”,0xff9923]// button3
[NoteIButton, “Create LP”,0xff9923]// button4
[VarSet,result,[Note,"\Cff9923 Please select low poly option?
",0x282f42,400]]
[If, result == 1,
[Loop, sDIV,
[IPress,Tool:Geometry:Lower Res]
]
[IPress,Tool:Geometry:Del Higher]
[VarSet, sDIV, 0]
[RoutineCall, Part2]
]
[If, result == 2,
[Loop, sDIV,
[IPress,Tool:Geometry:Lower Res]
]
[IPress,Tool:Geometry:Del Higher]
[VarSet, sDIV, 0]
[Note, “Please go Back to EaZy Exploder and hit Styx Used”]
[VarSet, styxUsed=1]
[IPress, Zplugin:Styx:ImportExport:Imp]
]
[If, result == 3,
[Loop, sDIV,
[IPress,Tool:Geometry:Lower Res]
]
[IPress,Tool:Geometry:Del Higher]
[VarSet, sDIV, 0]
[IPress, Tool:Import]
[RoutineCall, Part2]
]
[If, result == 4,
[IPress, Transform:PF]
[IPress, Transform:Solo]
[Loop, 9999,
[VarSet, ButtonNo2, 9]
[NoteIButton, “Double Polycount”,0xff9923]// button1
[NoteIButton, “Split Polycount”,0xff9923]// button2
[NoteIButton, “New Edge Flow”,0xff9923]// button3
[NoteIButton, “+1”,0xff9923]// button4
[NoteIButton, “-1”,0xff9923]// button5
[NoteIButton, “+0.1”,0xff9923]// button6
[NoteIButton, “-0.1”,0xff9923]// button7
[NoteIButton, Target Polygon Amount,0xff9923]// button8
[NoteIButton, “Done”,0xff9923]// button9
[VarSet,result,[Note,"\Cff9923 Make low poly
",0x282f42,400]]
[If, result == 1,
[IPress, Tool:Geometry:Double]
[IPress, Tool:Geometry:ZRemesher]
]
[If, result == 2,
[IPress, Tool:Geometry:Half]
[IPress, Tool:Geometry:ZRemesher]
]
[If, result == 3,
[IPress, Tool:Geometry:Same]
[IPress, Tool:Geometry:ZRemesher]
]
[If, result == 4,
[VarSet, Target Polygon Amount, Target Polygon Amount+1]
]
[If, result == 5,
[If, Target Polygon Amount>0.1,
[VarSet, Target Polygon Amount, Target Polygon Amount-1]
]
]
[If, result == 6,
[VarSet, Target Polygon Amount, Target Polygon Amount+0.1]
]
[If, result == 7,
[If, Target Polygon Amount>0.1,
[VarSet, Target Polygon Amount, Target Polygon Amount-0.1]
]
]
[If, result == 8,
[IUnPress, Tool:Geometry:Same]
[IUnPress, Tool:Geometry:Double]
[IUnPress, Tool:Geometry:Half]
[ISet, Tool:Geometry:Target Polygons Count, Target Polygon Amount]
[IPress, Tool:Geometry:ZRemesher]
]
[If, result == 9, //Without this one everything woks
[VarSet, ButtonNo3, 2]
[NoteIButton, “Yes”,0xff9923]// button1
[NoteIButton, “No”,0xff9923]// button2
[VarSet,result,[Note,"\Cff9923 Make new UVs?
",0x282f42,400]]
[If, result == 1,
[Note, “Please go Back to EaZy Exploder and hit UVs Used”]
[VarSet, makeUv, 1]
[IPress, Zplugin:Uv Master:Unwrap]
[IPress, Zplugin:Uv Master:Flatten]
]
[If, result == 2,
[RoutineCall, Part2]
]
[LoopExit]
]
]//end loop
]
]