Lady of Naga
Hello there. I'd like to share with you the process my latest work as this work's done in ZBrush has made its journey into a 3D print and then a Bronze Statue as the final product (Edition Size: 9 / Approximately 20" x 20" x 24" Weight roughly around 80 lbs / 36 Kilograms of Silicon Bronze)
The piece will be displayed at Thailand National Fine Art Exhibition 2012 in the coming month of February.
The year is 2012, The year of Water Serpent (Water Dragon) where the world shall be blessed with happiness. This piece depicts young maiden in harmony with the auspicious creature. Signifying affluence in wealth and happiness in the harmonious way should human treats nature. (This piece's actually conceived prior to the huge Flood in Bangkok at the end of last year)
This is one of the first Bronze statues with the use of Himmapan (Asian's heavenly forest) Theme. The project's being sponsored in parts by OCAC (Office of Contemporary Art And Culture, Ministry Of Culture ,Thailand), Post Element Co., Ltd--ComputerArts (Thailand), and Comgraph Co. Ltd.
It's worth to note that during the process of sculpting the piece, I utilized reference made by AnatomyTools.com (This one in particular http://anatomytools.com/products/anatomy/fig-female1a) And must also thank my master, Alex Oliver for teaching me the basics of Anatomy.
Last edited by SolidSnakexxx; 01-27-12 at 02:15 AM.
Excellent peace of art....
Conceptualize with Mannequin
The very first steps we, My girlfriend and I, did was roughing out the form of which we want the final pose in order to gain a proper space/composition of the piece. The best way I found out was to use the well thought out feature, Mannequin --which is highly under-rated. I in fact did several form sketches and finally settled with this pose. The human figure's the one in ZBrush pre-installed asset. The Water Dragon's made crudely with ZSphere just to fulfill its need as a design sketch.
Thank you so much. Glad you like it.
ZBrush Time - Fun Time
For the lady of Naga, I utilized DynaMesh feature to convert the form and sculpted non-symmetrically. The nature of DynaMesh allows me the freedom to sculpt. Small parts could be added in easily without restriction.
Last edited by SolidSnakexxx; 01-19-12 at 08:21 AM.
The Model of Naga followed the same method used for sculpting the Lady. As the piece will be printed out at a fairly large size (24" in height) I started to plan where to cut the models apart. With DynaMesh and Slice Tool, this can be accomplished easily.
Excellent patina work on that bronze btw.
Thank you very much. I think one of the most rewarding part about Bronze is its ability to hold such wide range of Patina so we could express just the tone we want. Really glad you like it.
Wax work prior to Bronze casting:
The Process we employed was Lost wax, for that we had to create silicone mould for the parts, and then the finalized wax version's produced. Then it's the task to do the final fine tuning work on the wax to progress further for Bronze casting.
Bronze Progress #1 :
Once it's cast in Silicon Bronze, the pieces were conjoined together once again and some Bronze refinement process begins.
Patina work's laid down with the basic tone / Generic Bronze prior to finalizing the patina to my liking.
Thanks for the inprocess pics. I'm sharing them with my traditional sculpture friends. I used to do a fair bit of bronze chasing and patina work for hire. Yah the patina is where all the hard work pays off.
Well done, I love dragons
Absolutely wonderful to see this process and thank you for sharing.
Top row for me
Right! This is in fact the first time I tried out his large print. Eventually my aim is (probably in the next few years) to create a larger than life Sculpture park of this magical forest in Bronze... (That's my dream anyway.... )
Thank you...and welcome to the year of Dragon!!
Thank you so much, really appreciate your comment. Glad you like the piece.